Eton 41.5cc Cylinder Head p/n 700121

Scooter gear Hardened 20 tooth Metal 5M Belt Gear Same size as factory small metal belt gear on transmission. This is the factory small metal gear for "the rock", this is the recommended belt gear for shaft as it is Hardened and wears slowly. Replace your worn out sprocket today and break less belts.

Drive Shaft Bearing #6201 SALE $8.60 each

Drive Shaft Bearing Snap Ring for Cobra, the Rock, Rockette, Dynamite III, Nuke, Lowrider Rock, StandR, commuter Holds shaft bearings in place.

Cobra or The Rock or Lowrider Rock, Nuke or StandR or Cobra "commuter" Driveshaft ONLY note: order 20t-5m & 60t-5m sprockets and spacer & bearings & 4mm keybar or snap rings separately

Drive Shaft made per order fits ScootR, Salorr, Staru, R3, Tiger, Rockfield, Libra T.H.S. & chuweng & Raser, FX. R1, R3, R4, R5 Use correct "pulley spacer" intended for use with one or two left side bearings between left side shaft pulley and bearing s? to avoid major shaft damage. Call scooterman @ 256.468.2761 & inspect frame to determine correct application of one or two left side bearings.

Drive Shaft Gear Snap Ring for Cobra, the Rock, Rockette, Dynamite III, Nuke, Lowrider Rock, StandR & 2013 ScootR or replacement Raser shaft. or use type 5 spacer

Drive Shaft Big Sprocket 4mm "Keybar" keeps lower left side bigger pulley from spinning on shaft

Stainless Steel Driveshaft Nut

Drive Shaft Spacer Type 1 & 2 for Lower Left Shaft 5m Belt Sprocket. Fits Raser, THS, SCOOTR, Tiger, R3, Star II, Rockville, Salorr, THX PRO & Libra, Cobra, the rock, lowrider rock, STANDR,Cobra commuter, rockette, dynamite III, and nuke scooters with This spacer goes between lower left side pulley and left side drive shaft bearing to keep bearing from damaging shaft. This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 720 thousandths long

Drive Shaft Spacer Type 3 Custom For Lower Left 5m Belt Shaft Sprocket when using 2 left side shaft bearings only! Some models/frames only benefit from extra left side bearing when primary bearing fails or shaft is worn where bearing rides.most models can carry 2 left bearings. call if need be. Fits many scooters if driveshaft bearing dwell in frame is exact same size for entire bore & is for custom improved application or temp fix only! not stock! This spacer goes outside or between lower left side drive shaft bearings x 2! If between two left bearings on Cobra you may need a washer or change pulley to our solid metal lower left pulley. This is for custom application only. Call before ordering! This spacer is only used when installing 2 left side bearings for which some frames don't retain the 2nd left side bearing. Call and we will explain. (256)468-2761 This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 340-350 thousandths long.

Drive Shaft Spacer Type 4 Custom For Lower Left 5m Belt Shaft Sprocket when using 2 left side shaft bearings only! Some models/frames only benefit from extra left side bearing when primary bearing fails. most models can carry 2 left bearings. call if need be. Fits many scooters if driveshaft bearing dwellin frame is exact same size for entire bore & is for custom improved application only! not stock! This spacer goes between lower left side pulley and left side drive shaft bearings x 2! Or between two left bearings on Cobra. This is for custom application only. Call before ordering! This spacer is only used when installing 2 left side bearings for which some frames don't retain the 2nd left side bearing. Call and we will explain. 256.468.2761 This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 400 thousandths long. use of type 3 spacer for this extra bearing setup is more common.