Stainless Steel Driveshaft Nut

Drive Shaft Spacer Type 1 & 2 for Lower Left Shaft 5m Belt Sprocket. Fits Raser, THS, SCOOTR, Tiger, R3, Star II, Rockville, Salorr, THX PRO & Libra, Cobra, the rock, lowrider rock, STANDR,Cobra commuter, rockette, dynamite III, and nuke scooters with This spacer goes between lower left side pulley and left side drive shaft bearing to keep bearing from damaging shaft. This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 720 thousandths long

Drive Shaft Spacer Type 3 Custom For Lower Left 5m Belt Shaft Sprocket when using 2 left side shaft bearings only! Some models/frames only benefit from extra left side bearing when primary bearing fails or shaft is worn where bearing rides.most models can carry 2 left bearings. call if need be. Fits many scooters if driveshaft bearing dwell in frame is exact same size for entire bore & is for custom improved application or temp fix only! not stock! This spacer goes outside or between lower left side drive shaft bearings x 2! If between two left bearings on Cobra you may need a washer or change pulley to our solid metal lower left pulley. This is for custom application only. Call before ordering! This spacer is only used when installing 2 left side bearings for which some frames don't retain the 2nd left side bearing. Call and we will explain. (256)468-2761 This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 340-350 thousandths long.

Drive Shaft Spacer Type 4 Custom For Lower Left 5m Belt Shaft Sprocket when using 2 left side shaft bearings only! Some models/frames only benefit from extra left side bearing when primary bearing fails. most models can carry 2 left bearings. call if need be. Fits many scooters if driveshaft bearing dwellin frame is exact same size for entire bore & is for custom improved application only! not stock! This spacer goes between lower left side pulley and left side drive shaft bearings x 2! Or between two left bearings on Cobra. This is for custom application only. Call before ordering! This spacer is only used when installing 2 left side bearings for which some frames don't retain the 2nd left side bearing. Call and we will explain. 256.468.2761 This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 400 thousandths long. use of type 3 spacer for this extra bearing setup is more common.

Driveshaft Spacer Type 5 goes Between Right Bearing & small gear to keep sprocket from walking or rubbing inside of frame. Specs-ID-600/1000ths OD-800/1000ths & is 200/1000ths wide. need for such a spacer to be determined by purchaser by measuring distance between edge of installed gear & right side bearing. not all shafts need such a spacer as some have gear snap ring like Cobra or can be welded. not for use with chain drive kits.

Drive Shaft With Hardened 20 tooth Belt Gear installed for Cobra & The Rock & Nuke & StandR & Lowrider Rock only!

ETON 40/41.5cc plastic engine cover P/N 700151

Engine crankcase and crankshaft with cylinder head and piston and spark plug & exhaust studs or bolts & gasket & intake gasket only. does not include carburetor, starter recoil or catch/ratchet or clutch shoes or flywheel or ignition coils,engine covers, external engine parts sold separately.

1 x crankcase gasket 2 x crankshaft bearings 2 x crankshaft seals

Eton 41.5cc Rubber Engine Mounts for scooters Set Of 2

Eton IXL 40 e-ton rxl 40 & 40E Engine Top End Rebuild Kit. P/n 810788 Includes cylinder head and cylinder gasket and exhaust gasket and piston and piston rings and piston wrist pin and needle bearing and circle clips and NGK BPM6A spark plug. Air and fuel intake parts separate.

Eton 40 ATV or older scooter Air Filter High Performance for Float Style Carbs. Comes with filter and filter clamp and velocity stack and gasket and two screws.