Drive Shaft Spacer Type 3 Custom For Lower Left 5m Belt Shaft Sprocket when using 2 left side shaft bearings only! Some models/frames only benefit from extra left side bearing when primary bearing fails or shaft is worn where bearing rides.most models can carry 2 left bearings. call if need be. Fits many scooters if driveshaft bearing dwell in frame is exact same size for entire bore & is for custom improved application or temp fix only! not stock! This spacer goes outside or between lower left side drive shaft bearings x 2! If between two left bearings on Cobra you may need a washer or change pulley to our solid metal lower left pulley. This is for custom application only. Call before ordering! This spacer is only used when installing 2 left side bearings for which some frames don't retain the 2nd left side bearing. Call and we will explain. (256)468-2761 This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 340-350 thousandths long.

Drive Shaft Spacer Type 4 Custom For Lower Left 5m Belt Shaft Sprocket when using 2 left side shaft bearings only! Some models/frames only benefit from extra left side bearing when primary bearing fails. most models can carry 2 left bearings. call if need be. Fits many scooters if driveshaft bearing dwellin frame is exact same size for entire bore & is for custom improved application only! not stock! This spacer goes between lower left side pulley and left side drive shaft bearings x 2! Or between two left bearings on Cobra. This is for custom application only. Call before ordering! This spacer is only used when installing 2 left side bearings for which some frames don't retain the 2nd left side bearing. Call and we will explain. 256.468.2761 This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 400 thousandths long. use of type 3 spacer for this extra bearing setup is more common.

Driveshaft Spacer Type 5 goes Between Right Bearing & small gear to keep sprocket from walking or rubbing inside of frame. Specs-ID-600/1000ths OD-800/1000ths & is 200/1000ths wide. need for such a spacer to be determined by purchaser by measuring distance between edge of installed gear & right side bearing. not all shafts need such a spacer as some have gear snap ring like Cobra or can be welded. not for use with chain drive kits.

Driveshaft Spacer Type 6 goes Between Right Bearing & small gear to keep sprocket from walking or rubbing inside of frame. Specs-ID-600/1000ths OD-800/1000ths & is 120/1000ths wide. need for such a spacer to be determined by purchaser by measuring distance between edge of installed gear & right side bearing. not all shafts need such a spacer as some have gear snap ring like Cobra or can be welded. not for use with chain drive kits.

ETON 40/41.5cc plastic engine cover P/N 700151

Engine crankcase and crankshaft with cylinder head and piston and spark plug & exhaust studs or bolts & gasket & intake gasket only. does not include carburetor, starter recoil or catch/ratchet or clutch shoes or flywheel or ignition coils,engine covers, external engine parts sold separately.

1 x crankcase gasket 2 x crankshaft bearings 2 x crankshaft seals

Eton 41.5cc Rubber Engine Mounts for scooters Set Of 2

Eton IXL 40 e-ton rxl 40 & 40E Engine Top End Rebuild Kit. P/n 810788 Includes cylinder head and cylinder gasket and exhaust gasket and piston and piston rings and piston wrist pin and needle bearing and circle clips and NGK BPM6A spark plug. Air and fuel intake parts separate.

Eton 40 Billet CNC Start Receiver 700168-CNC

Eton 40 Coil Mount Bolt Set of two bolts with 7mm head for easy coil adjustment on Black Thunder Coils These are the OEM coil mount bolts used on the green coil from factory

Eton 40 Ikeda Coil Harness This wiring harness replaces the trigger module when using the New Black Thunder coil, the wiring harness plugs onto the new ignition coil and then plugs right into the vehicle harness with two wires in a 3-pin plug. If you are purchasing the coil the coil will come with this wiring harness and an NGK spark plug so there would be no need to purchase this harness if you are purchasing the coil it is included.