#35 Shaft Sprocket 13 Tooth Hardened Fits 9 & 10 inch rear tire models With sprocket up inside frame

#35-12 & 13 Toothed Shaft Sprocket For Big Wheel Models Available Momentarily 13 tooth is for added torque. Select desired sprocket.

#35 Sprocket For Wheel 36 tooth Reccomended for use with 12 tooth shaft sprocket on 9 inch rear tire models only to retain factory gear ratio on The Rock, Cobra, Lowrider Rock, Nuke & StandR

#35 Sprocket For Wheel 40 Tooth Hardened Recommended for use with 13 tooth shaft sprocket to keep 3 to one factory gear ratio on Cobra, The Rock, Nuke, Lowrider Rock & StandR This sprocket will increase speed on all other models using 4 to 1 gear ratios, such as SCOOTR, Raser or or Rockville or Libra or StarII or Salorr with 9 inch rear tire. But is not recommended with 3.0-4/280x65 rear tires unless you don't care about hill pulling ability or potentially straining your clutch. Recommended wheel sprockets for 10 inch rear tires would be 45 tooth only. "Big wheel" models use 60 tooth wheel sprockets.

#35 Sprocket For Wheel 45 tooth p/n 2299k319 45 Tooth Hardened Wheel sprocket. Recommended for use with 12 tooth shaft sprocket to keep close to four to one factory gear ratio on most models excluding big wheel models and also The Rock/Cobra or Nuke/Lowrider/STANDR, BUT This sprocket will increase TORQUE on models using 3:1 OR 3.16:1 gear ratios, such as THS OR ROCK/COBRA with 9 inch rear tire. This sprocket is recommended with 3.0-4/280x65/10 inch rear tires For even MORE torque, use a 13 tooth shaft sprocket. "Big wheel" models use 60 tooth wheel sprockets.

#35 Sprocket For Wheel 48 tooth

#35 Sprocket For Wheel On Big Wheel models 52 tooth. can be used on 10 inch tire for torque or big wheel model for speed. This is the Cobra Extreme or Rocky factory wheel sprocket. This is for speed. for factory ratios on Raser big wheel order 60 tooth.

#40 Over Kill Chain Drive Kit #40 ansi roller chain kit for: The Rock, Cobra, Nuke, Lowrider Rock, STANDR, & ROCKETTE AND OTHER MODELS using 9 inch rear tire. Kit includes 3 feet of #40 ansi chain & master link, a 9 tooth #40 shaft sprocket and a 24 tooth #40 wheel sprocket. this is a non factory gear ratio of 1:2.7

This belt will fit our "Big Wheel" Scooters, BUT!! (It is weak) compared to the 5m-18 factory belt. We have even found that slight Shimming to Xcooter Thunder a.k.a. Raser Big Wheel a.k.a. PanthR models that have 102 tooth aluminum wheel sprockets with lip out can be shimmed behind sprocket to allow for running even 5m-20 belts. Not sure about Salorr Big Wheel model using 5m-20 yet without fipping both sprockets and maybe replacing wheel sprocket from plastic to aluminum 102 tooth sprocket from Chuweng.

1000-5M-18 BELT for big wheel models only such as Chuweng Raser "Big Wheel" & xcooter thunder & Salorr & Star II & Grizzly & PanthR & THS 04, THS 05. and others using 102 tooth 5m wheel sprocket This belt will fit our "Big Wheel" Scooters, BUT!! We have even found that slight Shimming to Xcooter Thunder. Atx 1000 a.k.a. Raser Big Wheel a.k.a. PanthR models that have 102 tooth aluminum wheel sprockets with lip out can be shimmed behind sprocket to allow for running even 5m-20 belts. Not sure about Salorr Big Wheel model using 5m-20 yet without fipping both sprockets and maybe replacing wheel sprocket from plastic to aluminum 102 tooth sprocket from Chuweng.

1000-5m-20 Belt Requires Sprocket shimming or swap or modification for use. We have even found that slight Shimming to Xcooter Thunder. Atx 1000 a.k.a. Raser Big Wheel a.k.a. PanthR models that have 102 tooth aluminum wheel sprockets with lip out can be shimmed behind sprocket to allow for running even 5m-20 belts. Not sure about Salorr Big Wheel model using 5m-20 yet without fipping both sprockets and maybe replacing wheel sprocket from plastic to aluminum 102 tooth sprocket from Chuweng.

1000 Belts that are 20mm Wide need Spacer/Shim for wheel sprocket to allow use of 1000-5m-20 belt.