Eton 41.5cc Cylinder Head p/n 700121

Drive Shaft Bearing #6201 SALE $8.60 each

Drive Shaft Spacer Type 3 Custom For Lower Left 5m Belt Shaft Sprocket when using 2 left side shaft bearings only! Some models/frames only benefit from extra left side bearing when primary bearing fails or shaft is worn where bearing rides.most models can carry 2 left bearings. call if need be. Fits many scooters if driveshaft bearing dwell in frame is exact same size for entire bore & is for custom improved application or temp fix only! not stock! This spacer goes outside or between lower left side drive shaft bearings x 2! If between two left bearings on Cobra you may need a washer or change pulley to our solid metal lower left pulley. This is for custom application only. Call before ordering! This spacer is only used when installing 2 left side bearings for which some frames don't retain the 2nd left side bearing. Call and we will explain. (256)468-2761 This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 340-350 thousandths long.

Drive Shaft Spacer Type 4 Custom For Lower Left 5m Belt Shaft Sprocket when using 2 left side shaft bearings only! Some models/frames only benefit from extra left side bearing when primary bearing fails. most models can carry 2 left bearings. call if need be. Fits many scooters if driveshaft bearing dwellin frame is exact same size for entire bore & is for custom improved application only! not stock! This spacer goes between lower left side pulley and left side drive shaft bearings x 2! Or between two left bearings on Cobra. This is for custom application only. Call before ordering! This spacer is only used when installing 2 left side bearings for which some frames don't retain the 2nd left side bearing. Call and we will explain. 256.468.2761 This is an improved spacer that is made in usa. Specs:ID-480/1000ths, OD-750/1000ths, 400 thousandths long. use of type 3 spacer for this extra bearing setup is more common.

ETON 40/41.5cc plastic engine cover P/N 700151

1 x crankcase gasket 2 x crankshaft bearings 2 x crankshaft seals

Eton 40 Ikeda Coil Harness This wiring harness replaces the trigger module when using the New Black Thunder coil, the wiring harness plugs onto the new ignition coil and then plugs right into the vehicle harness with two wires in a 3-pin plug. If you are purchasing the coil the coil will come with this wiring harness and an NGK spark plug so there would be no need to purchase this harness if you are purchasing the coil it is included.

eton 40 exhaust studs $2.00ea order two for a pair We now use a allen drive cap head bolt with integrated washers instead of factory exhaust stud. Reccomend Red locktite on exhaust bolts.

Fender Front Chromed keep water and mud down with a classic stylish oversized Chrome front fender, fits MANY different scooters with 10 inch tires

5m stainless steel button head allen drive deck screws with stainless washers and lock washers. A must for aftermarket footboards or stripped out factory holes in box frame. For the Rocky & Cobra Extreme the screw Holes in frame will have to be drilled and then tapped to a metric thread pitch of .80

These footboards are made in the U.S.A. FITS ALL MODELS after selection. Bare metal. we can powdercoat & griptape. Select options of model, powdercoating? griptape? Stainless hardware? has 6 screw holes & gas cap hole. Part of price is shipping, these footboards are thicker than factory and expensive to ship

Foot Peg Set With Rod For Cobra and chuweng scooters steel rod Aluminum pegs Select Big 1&1/2" or Big Big 2"